Selleys Roof and Gutter Silicone

Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.

Features

UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula.
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
#Cured sealant at area to volume ratios up to 2500mm2/L

Product Details
How to Use
Handy tips
*Warranty Information
Clean up
Videos

Where can this product be used?

Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights

What materials is this product suitable for?

Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND

Please contact your store to confirm avaliability, as some stores may have a limited range.

Size	310g Cartridge (Translucent, Grey and Black)
	300g Cartridge (Other colours)
	75g Tube (Translucent only)
Colours	Black
	Classic Cream**
	Cottage Green**
	Deep Ocean**
	Dune**
	Galvanised Grey
	Grey
	Ironstone**
	Manor Red**
	Monument**
	Paperbark**
	Surfmist**
	Translucent
	White
	Woodland Grey**
	**Colorbond colour matched
Technology	Neutral Cure Silicone
Use	Interior
	Exterior

Use in a well ventilated area. Avoid contact with skin and eyes.

Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.

Limitation:

• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use

For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.

* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.