Polyglaze Sparkling Wash
Polyglaze Sparkling Wash is a gentle wash specially formulated to give you a sparkling clean and shiny finish, with no streaks or water spotting.
Selleys Autofix Silicone Marine Sealant is a translucent, highly waterproof, neutral curing silicone with good adhesion to marine materials.
Features
- Cures to a tough flexible waterproof seal
- UV resistant
- Water and Weather resistant
- Salt spray resistant
- Detergent resistant
- Non-corrosive
- Vibration resistant
- Resists temperatures from –60°C to +180°C continuously or to +240°C intermittently
Where can this product be used?
- Sealing gaps, joints, cracks and for bedding of fittings
- Windows
- Hatches
- Fitting and instruments
- Locks nuts, bolts and plates to prevent vibration
- Insulated and waterproofs electrical connections
- Bonds and repair most marine materials
What materials is this product suitable for?
- Glass
- Painted and varnished wood
- Fibreglass
- Most Plastics#
- Most Metals*
- #Not suitable for polycarbonate, polyethylene or polypropylene plastics.
- *Will not adhere to copper, brass or zinc containing metals.
Please contact your store to confirm avaliability, as some stores may have a limited range.
| Size |
75g Tube |
| Colour |
Clear |
| Technology |
Neutral Cure Silicone |
| Use |
Interior |
|
Exterior |
- Thoroughly clean surfaces with mineral turpentine and dry.
- Pierce blind seal in tube and fit nozzle. Extrude with steady pressure, ensuring sealant is pushed onto the surface or into the joint. If used as an adhesive or gasket, apply sealant to one surface only and bring together within 3 minutes.
- Tool to a smooth finish, with a spatula dipped in detergent water.
- Clean up before sealant cures with mineral turpentine. Cured sealant can only be removed by scraping or cutting.
- After use, remove nozzle and replace cap on tube. Allow sealant to cure in nozzle and remove before next use.
Limitations:
- #Not suitable for polycarbonate, polyethylene or polypropylene plastics.
- Sealant cannot be painted over.
- Not suitable for below water-line seals unless used as a gasket which is held mechanically in compression.
- Not recommended for trafficable joints, such as open joints between deck planks.
- *Will not adhere to copper, brass or zinc containing metals.
- Not suitable for contact with petrol or distillate.
- Avoid smearing of excess sealant on surfaces as this can cause problems with painting.
- Use masking tape for a neat appearance or where clean up is difficult.
- Resistant to -60ºC and 180ºC continuously, or to 240ºC intermittently.
- Sealant cures in 24 hours in normal applications. If used as a gasket or adhesive up to 7 days may be required for full curing. If used to replace compression gaskets in port-hole closures, leave to cure a few days before fully tightening bolts/screws on the compression ring.
- During application a harmless vinegar odour is generated, but disappears as sealant cures.
- Uncured product may be removed with mineral turps.
- Cured product can be sanded and scraped.
Polyglaze Wash & Wax
Polyglaze Wash & Wax gives a spotlessly streak free finish with a noticeable shine in one easy step for a great result you can be proud of.
How to Guides
How To Create A Chopping Board
Keep on trend and learn how to create a stunning chopping board for serving which will be the envy of your friends at your next dinner party.
How To Fix A Splashback To A Wall
Sticking a splash back in a kitchen is a great way to improve the aesthetics of the kitchen. Selleys make the job easier with this step by step guide.
How To Makeover Your Kitchen In An Afternoon
The kitchen is the heart of every family home, but over time – cooking spills, kids, clutter can leave it looking a little tired. Here are some simple steps to giving it a refresh
How To Seal A Kitchen Splashback
Sealing your splashback is the final step to installing a splashback and perhaps the most important! It's super easy to do with Selleys silicone sealant.
Share
Share this product with your friends